Aufrufe
vor 5 Jahren

Broschüre VirTis AdVantage Pro

  • Text
  • Specifications
  • Lowest
  • Condenser
  • Maximum
  • Scientific
  • Vacuum
  • Aisi
  • Bspt
  • Latching
  • Benchtop
  • Www.bartelt.at
Broschüre VirTis AdVantage Pro

VirTis

VirTis AdVantage Pro Laboratory Benchtop Freeze Dryer Dimensional Data Shelf Configuration XL EL Shelf Clearance Shelf Area Width 22.2 in (565 mm) 22.2 in (565 mm) 1 Shelf 6.2 in (158 mm) 143 in 2 (922 cm 2 ) Depth 25.7 in (653 mm) 25.7 in (653 mm) 2 Shelves 2.9 in (73 mm) 286 in 2 (1,844 cm 2 ) Height 29.7 in (754 mm) 29.7 in (754 mm) 3 Shelves 1.75 in (44.5 mm) 429 in 2 (2,766 cm 2 ) Weight 310 lb (140 kg) 310 lb (140 kg) Nominal Shelf Size (W x D x TH): 10.2 X 14 X 0.4 in (260 X 355 X 9.5 mm) Chamber Construction Material of Construction AISI Type 316L SS Vacuum Pump (Required, not included) Additional Information Two-Stage Rotary Vane or Suitable Dry Pump Shelf Construction AISI Type 316L SS Defrost Type Hot Gas Chamber Door Full-View Acrylic Refrigerant CFC Free Condenser Coil AISI Type 316L SS Condenser Type Internal Four Port Manifold (Optional) AISI Type 316L SS Stoppering (Optional) Top-Down Pneumatic Quickseal Body (Optional) Neoprene Compressed Air Inlet (Stoppering Option) †† 1/4-inch BSPT fitting Quickseal Knob (Optional) Polypropylene Inert Gas Port 3/8-inch Hose Barb fitting Note: Dimensional data specifications are for standard AdVantage Pro lyophilizers. Specifications may vary based on optional components (i.e., optional four port manifold). * Shelf temperature is controlled to within ± 1.0 °C of the setpoint within the Shelf Temperature Control Range. † The Lowest Shelf Temperature and Lowest Condenser Temperature values may be lower than or equal to the Performance Specifications. ‡ Shelf pull-down times are based on tests performed with no load at “pre-seal” pressure (approximately 400-500 mbar). The increased mass of stainless steel and additional heat transfer fluid for units with more than one shelf will increase the pull-down time. Use the following multipliers when determining the pull-down time specification for the following shelf configurations: 2-shelf units, standard pull-down time x 1.5 and 3-shelf units, standard pull-down time x 2. Shelf temperature deviations shall not exceed the specification relative to the mean of the highest and lowest temperature readings. § SP Scientific can configure any unit to conform to the electrical requirements of a wide range of international voltage and phase configurations. The AdVantage Pro includes an IEC60320 C20 receptacle on the back of the unit. This receptacle allows for country-specific power leads to be supplied. Contact SP Scientific for more information. \ The specified Maximum Ice Condensing Capacity in 24 Hours and the Maximum Deposition Rate are based on the process of freeze-drying water as aggressively as possible. The freeze dryer's ability to collect ice at an hourly rate or over a specified period will always be application-dependent ** The optional shelf latching kit allows for two to one shelf latching on two-shelf units, which increases shelf clearance to 5.6 in (142.2 mm) and 3 to 2 shelf latching on 3-shelf units, which increases shelf clearance to 2.6 in (66 mm). 3 to 1 shelf latching is unavailable. †† The Advantage Pro is configured with a 1/4-inch BSPT bulkhead fitting. A BSPT to 1/4-inch NPT adapter shall be provided with the unit, which will allow users to choose between a 1/4-inch BSPT fitting and a 1/4-inch NPT fitting. Copyright © 2014 SP Scientific. All marks herein are used under license. All brand or product names mentioned may be trademarks or registered trademarks of their respective companies. SP Scientific reserves the right to change specifications without notice. Part Number 100007465 Rev 005, 12/14

News & Aktionen

Broschüren/Kataloge